Gasboy M06875K00X Uživatelský manuál stáhnout pdf

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 1

Introduction

This manual provides installation instructions for the Automatic Temperature Compensation

(ATC) Kits on Retail Atlas™ (8800K) units.

Note: Filters are required for installation but are not contained in the kits.

• M06875K001 for Single-Sided 8800K Unit

• M06875K002 for Two-Sided 8800K Unit

Contents

Required Reading

Before installing a kit, the installer must read, understand, and follow:

• This manual

• NFPA 30A, The Automotive and Marine Service Station Code

• NFPA 70, The National Electrical Code

• Applicable Canadian, federal, state and local codes and regulations

Failure to do so may adversely affect the safe use and operation of the equipment.

Note: This kit must be installed by a Gasboy Authorized Service Contractor (ASC) to ensure

warranty.

Section Page ...

Introduction 1

Required Reading 1

Required Tools 2

Abbreviations and Acronyms 2

Parts Lists 2

Important Safety Information 5

Installation 7

Preparing Site and Dispenser for ATC Option 7

Installing Filter Manifold and Probe 7

Installing the T-Meter Module and Cables 9

Installing I.S. Barrier Assembly 11

Installing ATC Controller Board 12

Connecting ISB Wires and Cable 15

Completing Installation 16

Programming the ATC Option 18

MDE-4556

Gasboy ATC Kits M06875K00X

Installation Manual

July 2006

1 2 3 4 5 6 ... 21 22

Shrnutí obsahu

Strany 1 - Introduction

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 1IntroductionThis manual provides installation instructions for the Automatic

Strany 2 - Required Tools

InstallationPage 10 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Figure 3: Cable Block Diagram for T-Meter Module3Route the T-M

Strany 3

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 11InstallationInstalling I.S. Barrier AssemblyThe kit parts used in this sect

Strany 4 - Related Documentation

InstallationPage 12 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Installing ATC Controller BoardUse the following guidelines wh

Strany 5 - Important Safety Information

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 13Installation2 Insert ATC Controller board into top slot of card cage.If nec

Strany 6 - Emergency First Aid

InstallationPage 14 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Figure 6: Cable Connections Between Boards for ATCexisting R19

Strany 7

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 15InstallationConnecting ISB Wires and Cable1 Remove junction box cover using

Strany 8

InstallationPage 16 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Figure 8: ISB to ATC Controller and T-Module Assembly Connecti

Strany 9

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 17Installation4 Do an ATC master reset on T20569-G1 ATC Controller board by i

Strany 10 - Installation

Programming the ATC OptionPage 18 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Programming the ATC OptionSwitch ON the programm

Strany 11

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 19Programming the ATC OptionHow To Access ATC Mode InformationExample of How

Strany 12

IntroductionPage 2 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Required ToolsThe following tools are needed to install the ATC

Strany 13

Programming the ATC OptionPage 20 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 301 Display Volume Correction Factor (VCF)• Mone

Strany 14

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 21Programming the ATC OptionATC Error CodesThe following list describes ATC e

Strany 15 - Controller board (Figure 8)

Strany 16 - Completing Installation

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 3IntroductionM06875K002 - ATC Kit for 115 VAC Two-Sided UnitQ13130-01 Thermow

Strany 17

IntroductionPage 4 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Related DocumentationDocument Number Description GOLD LibraryMD

Strany 18 - Programming the ATC Option

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 5Important Safety InformationImportant Safety InformationThis section introdu

Strany 19 - 300 View Last Transaction

Page 6 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006Important Safety InformationNo Open FlamesOpen flames from matches, lighters

Strany 20

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 7InstallationInstallationPreparing Site and Dispenser for ATC Option1 Record

Strany 21 - ATC Error Codes

InstallationPage 8 MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 2 Unbolt and carefully remove current M04607B001 Valve and Filt

Strany 22 - Pump Error Codes

MDE-4556 Gasboy ATC Kits M06875K00X Installation Manual • July 2006 Page 9InstallationInstalling the T-Meter Module and CablesThe cables used in this

Komentáře k této Příručce

Žádné komentáře

Gasboy M06875K00X Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Gasboy M06875K00X. Gasboy M06875K00X User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Hardware Gasboy M06875K00X