Gasboy EQ 25 XXX Uživatelský manuál stáhnout pdf

MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 Page 1

Introduction

This manual provides installation instructions for the following Gasboy Pulser Kits:

Required Reading

Before installing a kit, the installer must read, understand, and follow:

• This manual

• NFPA 30A, The Automotive and Marine Service Station Code

• NFPA 70, The National Electric Code

• Applicable federal, state and local codes and regulations

Failure to do so may adversely affect the safe use and operation of the equipment.

Note: This kit must be installed by a Gasboy Authorized Service Contractor (ASC) to ensure

warranty.

Required Tools

The following tools are needed to install the Pulser Kits:

• Standard Wrench Set

• Flat tip screwdriver

• Cross tip screwdriver

• Punches (to remove and install pins)

Kit number Kit Description

032796 Pulser Kit X:1 EQ 25 GAS

033088 Pulser Kit X:1 EQ 25 LTR GAS

033140 Pulser Kit X:1 EQ 25 LTR DSL

033148 Pulser Kit X:1 EQ 25 DSL

MDE-4485

Gasboy Pulser Kits X:1 EQ 25 XXX

Installation

June 2005

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Introduction

MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 Page 1IntroductionThis manual provides installation instructions for the following

Strany 2 - Parts Lists

IntroductionPage 2 MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 Parts Lists032796 - Pulser Kit X:1 EQ 25 Gas033088 - Pulser Kit

Strany 3 - Important Safety Information

MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 Page 3Important Safety InformationThis section introduces the hazards and safety pr

Strany 4 - Emergency First Aid

Important Safety InformationPage 4 MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 No Open FlamesOpen flames from matches, lighters

Strany 5 - Replacing the Pulser Meter

MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 Page 5Installing the X:1 EQ 25 XXX Pulser KitInstalling the X:1 EQ 25 XXX Pulser Ki

Strany 6 - Installing the Pulser Module

Installing the X:1 EQ 25 XXX Pulser KitPage 6 MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 Figure 1: Meter Mounting (Left Side V

Strany 7 - Testing/Checking Operation

MDE-4485 Gasboy Pulser Kits X:1 EQ 25 XXX Installation • June 2005 Page 7Installing the X:1 EQ 25 XXX Pulser KitFigure 2: Placement of M06028A001 Puls

Strany 8 - Completing Installation

Installing the X:1 EQ 25 XXX Pulser Kit© 2005 Gilbarco Inc. 7300 West Friendly Avenue • Post Office Box 22087Greensboro, North Carolina 27420 Phone (

Komentáře k této Příručce

Žádné komentáře