Gasboy 9800A Uživatelský manuál stáhnout pdf

032024 Rev 1212 Page 1

INSTALLATION INSTRUCTIONS FOR HIGH HOSE RETRIEVER

FOR MODEL 9800A/2600A WITH VAPOR RECOVERY

This instruction sheet covers the installation of the Model 9800A/2600A Balanced System Vapor Recovery Kit.

If you ordered a vapor recovery kit, 032045, you should have received the following:

Item Part No. Description

1 030314 HHR Reel, Premier VR

2 063838 Support Bar, HHR 9800

3 017930 Caplug, 1-1/2 Sq. Tube

4 051956 Screw, 5/16-18x2, SS

5 068079 Washer, 5/16, SS

6 068874 Washer, Std Spring Lock, 5/16, SS

7 056927 Spacer, 1-1/2 x 1-1/4 dia.

8 013250 Bolt, 5/16 Mach Anchor, HHR

9 047219 Plug Button, 7/8

10 051957 Screw, 5/16-18 x 2-1/2, SS

11 064560 Swivel, Hose, 3/4, #36S

12 038502 Nozzle, Emco VR A4005 Stg II

Item Part No. Description

13 030301 Hose, Goodyear, Premier Coax, 7’6”

14 066817 Splitter, Emco, 4041-002

15 030407 Hose, 3/4" x 1’6” HW UL

16 017270 Bushing 3/4 x 1”

17 044007 Breakaway Coupling, Coax, Emco,

#A4019-1

18 030303 Hose, Goodyear, Premier Coax 4’6”

19 003336 Boot, Nozzle, VR

20 003719 Hook, Nozzle, VR

21 032024 Installation Instructions (this sheet)

22 035282 Warnings and Safeguards Sheet

1. Read all the instructions before beginning. A separate instruction sheet is packed with the Emco Wheaton

splitter manifold, which is required for mounting this component. Also read and follow all precautions

regarding remote dispensers and pumps on the Warnings and Safeguards sheet, 035282 (included in this

kit).

2. Turn off power to the dispenser at the breaker and activate emergency shutoff valve.

3. Item 14 must be mounted to the unit using the template and instructions furnished by Emco Wheaton.

4. Item 7 mounts between HHR post and side panel.

5. Item 8 requires a 5/8” diameter x 1-3/4 deep hole in the island.

6. Item 16 is required for units with 1” discharge assembly.

7. Item 17 must be installed approximately 12” downstream of hose retractor clamp.

8. To reduce the risk of accidental dispensing of fuel, turn off all power.

9. Use UL-Listed gasoline resisting compound on all joints of gasoline handling fittings. Sealing compound

must also be resistant to gasohol (ethanol and methanol). Do not use Teflon pipe sealing tape. Use

gasoline resistant pipe compound on all male threads only.

10. Tighten all hardware. Plug hole in post with Item 9.

Mounting of Nozzle Boot and Nozzle Hook

1. Remove the 4 screws from the existing nozzle boot and remove nozzle boot. Add new nozzle boot (item

19) with existing screws.

2. Remove hardware from existing nozzle hook.

3. Remove two plugs from lower mounting holes of side panel and plug upper holes.

4. Install new nozzle hook (Item 20) in lower holes with existing hardware.

1 2

Shrnutí obsahu

Strany 1

032024 Rev 1212 Page 1INSTALLATION INSTRUCTIONS FOR HIGH HOSE RETRIEVERFOR MODEL 9800A/2600A WITH VAPOR RECOVERYThis instruction sheet covers the in

Strany 2 - Mounting of Hose to Retriever

032024 Rev 1212 Page 2Mounting of Hose to Retriever1. Fit and tighten the clamp on the retriever at approximately the center of the length of hose.

Příbuzné modely 2600A

Další dokumenty pro Hardware Gasboy 9800A

Zobrazit dokument Gasboy 9800A Uživatelský manuál

Gasboy 9800A Uživatelský manuál (2 stránky)

Gasboy 9800A Uživatelský manuál (4 stránky)

Gasboy 9800A Uživatelský manuál (1 stránky)

Gasboy 9800A Uživatelský manuál (3 stránky)

Gasboy 9800A Uživatelský manuál (12 stránky)

Komentáře k této Příručce

Žádné komentáře

Gasboy 9800A Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Gasboy 9800A. Gasboy 9800A User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 2600A

Další dokumenty pro Hardware Gasboy 9800A

Komentáře k této Příručce

Související produkty a manuály pro Hardware Gasboy 9800A